Brick walls are stronger mounting surfaces than drywall: but they require completely different tools, anchors, and technique. Use a standard drill on brick and you'll burn out the motor without making progress. According to Simpson Strong-Tie's anchor load testing data, properly installed 3/8" sleeve anchors in solid brick hold 400–600 lbs each in shear, far more than any residential TV mount requires. Here's the complete guide.
Brick vs. Drywall: What's Different
Three things change when mounting on brick instead of drywall:
- Tools: You need a hammer drill (rotary hammer) with masonry bits, a standard drill won't penetrate brick effectively.
- Anchors: Wood screws into studs don't apply. You need masonry anchors rated for the TV's weight.
- Dust: Drilling brick creates significant brick/mortar dust. Have a vacuum or plastic sheeting ready.
Tools and Materials You Need
Do not use plastic expansion anchors on brick. They're rated for drywall loads and will pull out under a TV's repeated load cycles (vibration, repositioning). Always use metal masonry anchors, sleeve anchors or wedge anchors.
Brick vs. Mortar: Which to Drill?
You have two options: drill into the brick face itself, or drill into the mortar joints between bricks.
Mortar joints are usually preferred because:
- Easier to drill, mortar is softer than brick
- Easier to repair if you ever move the mount (re-point with matching mortar)
- Repairing a hole in brick face is cosmetically more visible
The tradeoff: mortar can be inconsistent, old homes may have soft mortar that doesn't hold as well. If mortar crumbles when drilled, switch to drilling the brick face with appropriate masonry anchors.
Step-by-Step: Mounting on Brick
Find the right mounting height
Mark the target center height for the TV with a pencil. For most living rooms, TV center should be at seated eye level, about 42–48" from the floor. Use a level to draw a horizontal reference line at mount-top height.
Identify your drill locations
Hold the wall mount bracket against the wall at your target position. Mark each hole location with a pencil. Decide whether to drill into brick or mortar based on where the holes fall. Try to keep all holes on one type (all mortar or all brick) for consistency.
Drill pilot holes with the hammer drill
Set the hammer drill to rotary hammer mode. Use a 3/8" masonry bit (match to your anchor diameter). Drill straight in, don't angle. Depth should equal anchor length plus 1/4". Keep the drill moving at steady pressure; don't force it. Clear dust every few seconds by pulling the bit out slightly.
Clean out the holes
Use a vacuum or blow out each hole with compressed air. Loose dust prevents anchors from seating properly and reduces holding strength.
Insert masonry anchors
For sleeve anchors: insert the anchor into the hole and hand-tighten the nut until snug, then torque with a wrench until the sleeve expands and grips the brick. Don't overtighten, you can crack mortar. The anchor should feel solid with no movement.
Attach the mount bracket
Thread bolts through the mount into the anchors. Tighten gradually and evenly across all bolts. Check level before final tightening. Pull-test the mount by applying firm outward and downward force, it should not flex or move.
Hang the TV
Attach the mount plate to the TV per the bracket instructions. Have a second person help lift the TV, especially for 55"+ screens. Hook onto the wall bracket and ensure it's fully seated and locked.
Common Mistakes on Brick Mounting
- Using a regular drill: Will overheat and fail. The hammer action of a rotary hammer is what breaks up the brick/mortar; a standard drill only rotates.
- Plastic anchors: Never adequate for brick mounting. Use metal masonry anchors only.
- Drilling near brick edges: Avoid drilling within 1" of a brick edge, you risk cracking the brick face. Drill in the brick center or mortar joint.
- Skipping the pull test: Always test the mounted bracket before attaching the TV. Push it firmly in all directions. If there's any movement, the anchor didn't expand fully, remove, clean the hole, and reinstall.
When to Call a Professional
Brick mounting is DIY-feasible if you have the right tools and time. Consider professional installation if:
- You don't own a hammer drill (renting adds time and cost)
- The brick is very old (pre-1920 soft brick) or visibly crumbling
- You're mounting above a fireplace on a masonry chimney
- The TV is 75" or larger and requires a 6-bolt pattern
- Wire concealment is also needed (surface raceways on brick require specific techniques)
Have a Brick Wall? We Handle It Daily
TV Mount Experts installs on brick, concrete, stone, and all masonry surfaces. Same-day available from $238 for a 32–59 inch TV.
Call: (213) 556-4558Frequently Asked Questions
Can you mount a TV on painted brick?
Yes. Painted brick mounts the same way as unpainted, the paint doesn't affect anchor holding strength. The main difference is aesthetics: drilling will chip the paint slightly around the hole. Use a masonry bit with the hammer drill as usual.
What's the weight limit for brick mounting?
Properly installed masonry anchors in solid brick hold 200–500 lbs each. A 4-anchor installation provides 800–2,000 lbs of theoretical holding strength, far exceeding even the heaviest consumer TVs (110" commercial displays weigh ~200 lbs). The practical limit is the mount bracket's weight rating, not the brick.
How do I fill the holes if I move the TV?
For mortar joint holes: use pre-mixed mortar or a masonry patch compound, color-matched to your existing mortar. For brick face holes: masonry patch compound works, but color-matching is harder on aged brick. Professional tuck-pointing can make repairs nearly invisible.