About Our Seattle Service
Seattle homeowners care about clean interiors, dangling TV cables are the first thing guests notice. We route them invisibly throughout Capitol Hill, Queen Anne, and Ballard.
Seattle's mix of construction types affects the approach. Older homes in Capitol Hill often have plaster walls or older drywall with inconsistent stud spacing. Newer construction in Bellevue and Redmond uses standard 16-inch OC framing, making in-wall routing straightforward.
Wire Concealment Methods for Seattle Homes
- In-wall routing with recessed outlet: HDMI and power run inside the wall to a recessed plate behind the TV; most Seattle and Eastside houses are wood-framed with open stud bays.
- Cord cover raceways: Capitol Hill and South Lake Union apartments usually rule out cutting drywall, so a paintable raceway hides the cords instead.
- In-wall routing above fireplace: after we locate the flue inside the chase, the cable drops down to a plate beside the hearth. $149.
- Baseboard channel routing: exterior walls are packed with insulation, so we push the cable through with a glow rod or use a low baseboard channel.
Pricing in Seattle
| Service | Price |
|---|---|
| Cord cover raceway (no drywall work) | +$69 |
| In-wall concealment with recessed power outlet | +$99 |
| In-wall routing above a fireplace | +$149 |
| TV mounting 32"–59" + in-wall wiring | from $268 |
| TV mounting 60"+ + in-wall wiring | from $288 |
Get an Exact Quote for Your Seattle Home
Answer 3 quick questions, we'll text you a price in under 2 minutes.
Call +1 (206) 258-6297Service Areas in Seattle
Frequently Asked Questions
Can you hide TV wires in my Seattle home without cutting the wall?
Yes. A paintable raceway hides the cords without opening the wall, which is what most Seattle apartment and condo rules allow. Moving out of a Capitol Hill unit means backing out four screws and dabbing the pinholes.
How much does TV wire concealment cost in Seattle?
A cord cover is $69. In-wall routing with a recessed outlet is $99 on a regular wall and $149 above a fireplace. Prices are the same in Seattle, on the Eastside and in Snohomish County.
Do you need to cut drywall to hide TV wires in Seattle?
Only for in-wall routing: one small opening behind the TV and one near the outlet, both finished with recessed plates, so nothing needs patching. Raceways don't need any cutting.
Can you hide wires on a brick or stone wall in Seattle?
Brick and stone can't be fished, so we run a slim raceway along the edge of the masonry and paint it to match. If the wall next to the fireplace is framed, the cable can go inside that wall instead.
Do you serve all Seattle areas for wire concealment?
Yes, across Seattle, Bellevue, Kirkland, Redmond, Renton, Everett and Tacoma, including Ballard, Fremont, Capitol Hill, Queen Anne, West Seattle and the Eastside suburbs. Same-day wire jobs are common when you call in the morning, and we text the arrival window.
Hiding TV Cables in Seattle Homes
Old plaster in Wallingford and Ballard, fresh drywall in Woodinville, the walls differ, but the goal is the same: nothing dangling below the screen.
Ballard: 55" tilting, cables inside, soundbar underneath
We supplied the soundbar bracket so it lines up exactly with the TV above, then pulled power and HDMI down inside the cavity to a plate behind the console. One clean vertical line instead of three cords.
Full-motion 55" with in-wall wiring in West Seattle
Articulating mounts need slack in the cable, so we leave a service loop behind the TV before it enters the wall. That way the arm can extend fully without yanking a connector out of the set.
Woodinville: two 75" sets and a 65", in-wall runs
Three screens across the house, with the main room's cabling run through the wall to the equipment below. On newer framing like this we check for fire blocking between studs before planning where the cable will drop.
Plaster, drywall and raceways in Seattle
Pre-war Seattle homes often have plaster and lath that crumbles if cut carelessly; we score it and drill slowly, or recommend a paintable raceway when the wall is fragile. Condo buildings downtown usually have concrete or steel-stud walls where in-wall runs are limited, raceways are the practical answer there.
Hidden-Wire Jobs in Seattle
A 55" Frame with a soundbar and the cable inside
A Queen Anne condo where the owner wanted a Frame on the living-room wall, with the One Connect cable and the soundbar cable hidden inside.
The technician arrived 50 minutes after booking. The building had steel studs, which the scanner and a magnet confirmed. He used toggles rated for steel studs for the slim mount and fished both cables down one bay to a plate by the console.
The Frame was laser-leveled and set flush. The soundbar went below it, and Art Mode and ARC were tested.
A 52" Frame moved and wired in-wall in Seattle
The Frame moved from the bedroom to the living room, this time with its cable inside the wall.
The technician arrived at the booked time. He took the Frame and slim mount down, filled the old holes, scanned the new wall and fished the One Connect cable. The Frame was set flush and tested in Art Mode.
Customer Reviews
Evan arrived promptly ready to get the job done. Made suggestions and offered the best solutions. I will request him EVERY TIME!!!! Mounted 2 60+ TVs quickly and effectively. He is nothing short of AMAZING…. Give him a raise and more stars😉.
Looks amazing and was quick and efficient
Evan was awesome. Did a great job fast and was super professional
Evan was polite, quick, and very professional. I’d recommend him to anyone.
Evan did a great job, was communicating the steps through the whole process and was very friendly! will definitely be back if there’s anything else i need especially if Evan can do the job!




